Making a wooden case

Some items need packaging. For example, if you want to present valuable, which is expensive. If you just donate a thing wrapped in cellophane, it will reduce the value of the gift. Packaging may also be necessary to permanently store some valuable items. One of the highest quality and beautiful materials for the manufacture of cases is wood. In this article, we will look at how to make a wooden case for any thing, but for a specific example, we will consider making a wooden case for a flute.
Making a wooden case

Case dimensions

Before you get started, you need to decide on the size of your case. It depends on what you want to put there? To do this, you need to measure the thing that you are going to store in it, but the case is better to make a few centimeters more so that this thing easily fit in it along the width, length and height. For example, the size of a flute is 45x3x3 cm.Therefore, the internal size of the case will be 50x6x5 cm.

Material

Now that you know the size, you need to pick up wood. For the manufacture of cases any type of wood may be suitable, but the most suitable and aesthetic will be solid varieties of wood (oak, beech, ash). In this example, the illustration uses ash with a beautiful texture.
Making a wooden case

Making

Prepare slats of the required length. Correct the length, cutting unnecessary, you can use an electric jig saw. In our example, the internal size of the case is 50x6x5 cm. Since the case consists of two parts (the lower part where the flute and the lid will go), in order to get a total height of 5 cm, it is necessary to make the lower part 3 cm high and the lid 2 cm high. All slats must be glued with glue "PVA", and pulled off for a few hours with clamps. After the glue has dried, you can start polishing the tree.
Making a case from wood
Making a wooden case
Making a case from a tree
In order to polish hardwood, it is best to use a grinder with a coarse sandpaper. Some places are more convenient to grind by hand. Sanding is necessary until you get smooth and smooth all the walls of the case.
Making a case from wood
Making a case from a tree
Next, for aesthetics, you can round the corners of the case with a manual cutter. The top cover of the case can be cutter on all sides, and the bottom cover is only in the middle, making a kind of legs. This will give your packaging a tracery.
Making a case from wood
Making a case from wood
Making a wooden case
Then you can start painting the case. For toning wood wood stain is used. Before you buy a stain, think about the tone of wood you want to get? Usually,on the labels of the cans of wood stain is illustrated the tone of the tree, which is obtained from this painting. "style =" max- width: 100%; " alt="Making a case from a tree">
Making a wooden case
Using a brush, apply stain to the wood. Then to protect the tree from moisture and other negative influences, varnish the case. It is best to apply several layers. You can use a glossy varnish that will give shine to the wood. Making a case from a tree
Making a case from wood
When the varnish is dry, you can attach the fittings. First, attach the hinges. To do this, retreat an equal distance from the edges, (in this case, 5 cm), and with the help of a drill, drill holes for hinged self-tapping screws, then tighten them with a screwdriver. "style =" max- width: 100%; " alt="Making a case from a tree">
Making a case of wood
It is best to drill holes, because if you immediately start to tighten the screw, the wood can crack. Then attach the front cover of the case exactly in the middle.
Making a wooden case
Most often, these locks are mounted on nails, which are sold in the kit. Nails can be hammered with a small hammer. It will also be practical if you put a limiter inside, which will keep the top cover in the required mode.
Making a wooden case
Thanks to the limiters, the top cover will not fall back too much, and at the same time it will not hit you on the fingers. Now you can proceed to interior decoration with a cloth. As a material in this case, it is better to use velvet or velor. You can choose the color of the fabric to your taste. Measure the pieces of foam to glue them to the bottom and top of the case.

Related News


Napkin Topiary
Rhubarb and raspberry fill tart
Christmas Magnet
How to drill a file
Cherry Pie Recipe